View previous topic :: View next topic |
Author |
Message |
Robson Vieira
Joined: 05 Jan 2017
Posts: 37
Location: São Paulo
|
Posted: Dec 23, 2019 10:33 Post subject: Black thin layer help id |
|
|
Hi everyone. I have found a little piece of basalt and it has a thin layer of a shiny black which I would like to know what it is. Follow the features of the LAYER only
Color: dark brown to black
Luster: submetallic
Streak: ochre to black
Hardness: 3 to 3,5 scratched by a fluorite chunk
Cleavage: none
The stuff is brittle a little bit.
Would it be just a chemical or organic deposition material?
The piece was found in a basaltic region.
Thanks
Mineral: | Unknown |
Description: |
North São Paulo State 6 x 3 cm |
|
Viewed: |
9588 Time(s) |
|
Mineral: | Unknown |
Description: |
North São Paulo State 6 x 3 cm |
|
Viewed: |
9596 Time(s) |
|
Mineral: | Unknown |
Description: |
North São Paulo State 6 x 3 cm |
|
Viewed: |
9593 Time(s) |
|
Mineral: | Unknown |
Description: |
North São Paulo State 6 x 3 cm |
|
Viewed: |
9589 Time(s) |
|
|
|
Back to top |
|
|
vic rzonca
Joined: 18 Nov 2008
Posts: 820
Location: MA
|
Posted: Dec 23, 2019 11:15 Post subject: Re: Black thin layer help id |
|
|
I would say it what's called a slickenside. It's a smoothly polished surface caused by frictional movement between rocks along the two sides of a fault. I collect in basalt's and have seen very large areas covered with this formation along fault zones.
|
|
Back to top |
|
|
Robson Vieira
Joined: 05 Jan 2017
Posts: 37
Location: São Paulo
|
Posted: Dec 23, 2019 12:15 Post subject: Re: Black thin layer help id |
|
|
Thanks vic. Its very cool fact. But how about the low hardness? I guess the material of the slickenside should be the same of the rock, wich is basalt in this case, that has high hardness. Maybe, the friction caused the decreasing hardness of the layer, i dont know?!
|
|
Back to top |
|
|
vic rzonca
Joined: 18 Nov 2008
Posts: 820
Location: MA
|
Posted: Dec 23, 2019 12:36 Post subject: Re: Black thin layer help id |
|
|
I don't know all the metamorphic products that would be formed in the heat and pressure involved in that friction zone, but, some one of the learned folks here might have an idea. It could be a serpentine, hardness 3-6.
|
|
Back to top |
|
|
David Mustart
Joined: 17 Dec 2011
Posts: 13
Location: San Francisco
|
Posted: Dec 23, 2019 14:36 Post subject: Re: Black thin layer help id |
|
|
How about a pic of the opposite side of specimen?
If it is reddish brown, then possibly the shiny surface is desert varnish, a result of manganese deposition on exposed surface.
_________________ David Mustart
Professor of Geology
San Francisco State University |
|
Back to top |
|
|
Robson Vieira
Joined: 05 Jan 2017
Posts: 37
Location: São Paulo
|
Posted: Dec 23, 2019 19:13 Post subject: Re: Black thin layer help id |
|
|
A genius idea David Mustart, thanks. Exactly as you had stated. The sample is brown at the opposite side. Would you say it solved the question? How can I detect the Mn presence to elucidate the ID?
Thanks
|
|
Back to top |
|
|
|